Hi TravAZ, if I understand correctly, the block isn't threaded NPT? I wish companies that manufacture consumer products, would...together, STANDARDIZE their wares so we as...consumers... didn't have to mix fittings. Oh well...back to the store I go.
Posts by Lui
-
-
Hi Kyle, thanks again for the help. I don't think that I will be removing the intake at this point. I will however be able to install the oil fitting at the rear of the head. There is lots of room to work. The question I have is, how much of a pressure drop is there going to be? I hope you have a good time in the Dominican!
-
Your best bet would be to T into this sending unit near the bottom of the block.
Hi Kyle, I looked at the pressure switch, and noticed that without the removal of the engine, it would be a bit..h to get at. The other item to consider for me, is that my oil pressure gauge has a tube that will run to it. Having said that, I think that running the line from the back of the head might be better? What are your thoughts on this?
-
Hi All, I am installing an Autometer, oil pressure gauge, so it would help if I knew where to put the sensor on the motor? LoL. I've searched this site, and I am at a loss.
-
Toronto is a great City, but I love the Niagara region now.....that I can ride to awesome wineries in minutes of me.
-
Effin cold!!! Effin rain!!!
-
I tip my hat to you Orangeman. Cheers
-
I might take on a bullet proof engine build this winter. As soon as I find a good block to start with. I wonder if it's possible to have dual SCs installed?
-
Hiya all, the SC kit comes with an adjustable blow off valve, and I was wondering if there is a certain position of the valve, or can't be adjusted to a specific setting for different results?
-
Oh..oh!!! I can hear the empty echos from another Slingshot owner's wallet...but...a very happy owner!
-
Hi, I installed a JL amp under the passenger seat...added JL 650 speakers to the front ssv pods, rear humps, and side pods. I ran all wires down the sides and behind the seats. Power was taken from the harness that feeds the radio. The system sounds great....so far... LoL.
-
It's getting Effing cold here in southern Ontario!!!!
-
I wonder how long it would take to get this delivered?
-
ROFLMFAO...I am wondering if this is something safe to use...and it won't leave residue of any kind?
-
Today on the news, they said that there has been a huge scientific breakthrough...there is a direct correlation between the feeling of heat, and the ambient temperature surrounding the body. Recent studies have shown that any person living in warm regions, should not flaunt their ambient temperature, as this may cause sudden head aches. It has also been said that some Canadians have been know to hurl frozen snow balls, in a southerly direction.....That is all.
-
I had my rims powder coated Pearl white to match my 2016.5 SLLE body colour. I had them done for $350.00 Canuk dollars. They look awesome, and a hell of a lot cheaper than buying new rims!
-
Mmmmmm....Sushi!!! Yes wasabi will clear all the duct work in the head. Let us not forget to have warm Saki to wash it all down!
-
This message is for all people's living in warm places....Go away! Stop making me feel more bitter than I already am! I am freezing my pinkies off, doing mods in my garage...yes no heat...yet! I am jealous...I can't wait for the really hot weather so I can bitch about that too...lol...so having said that... "where's the heat!" Please send up here to Canuk Land?
-
Thanks for the info. I am moving the switches to another location. As I said, I checked the switch terminals with my meter and the contacts positions don't make sense with the wiring.
-
This is how I did mine. I am happy with it.
CDCAMEL6
Hi Cdcamel6, I am changing the location of my switches as you have done. I checked the switch terminals with a meter, and they don't make sense. Can you please guide me through the process?