i found some black bolts at my hardware store i am going to use since my outer part is painted black. if you need anything else please let me know.
Care to share what style/type hardware you settled on? Most of the hardware store black coated bolts tend to rust.
A bolt expert friend of mine said he prefers zinc hardware and ships it off to be coated black.
The hardware I used are flat head aluminum bolts and nuts used for screen doors. Got it from Ace Hardware.
Aluminum? Hmmm, no issues with them coming loose?
@kenny_h I like that idea for gasket material and will seek some out in black.
Still not 100% sure on how to bend these, but will give it a shot. I didn't even consider having to shape the overall vent to match the contour of the fender. I'll be sure to take a peek. I had planned to measure and mark out the cuts before bending the fins, but now think that is the wrong approach.
I should set the fins, then shape the vent to match the contour and then measure for cuts.
I like the idea of adding additional mounting points to help keep these secured and will mirror that. what type of bolts/screws did you use? They looks awfully flat. Was considering riveting them on myself with a backer to spread the load.
Found one, never saw them again.
They should/ better take care of issue. No matter what shape item should be wrapped/ Protected, especially because there items aren't cheap!! ! I ordered a carbon wing and it could of fallen out of a truck on the highway and not be scratched with how well CS's wrapped it...Im guessing they take out insurance????
I am confident they will take care of it. How fast is the concern. I sent email over the weekend. No response today. Will call them in the morning since we are on opposite coasts.
do people with low rear exit pipes have this fume issue? What about side exit pipes?
Those with the rear exhaust pointing toward the back tire and remaining down low are not complaining about fumes with my combination. But I can't give up the looks of the dual setup now. It just looks right.
I take pictures of all my damaged boxes.... Before I open them...ideally you should meet the delivery guy and point out any box damage....these guys are under so much pressure to make fast delivers and the companies don't care because they have insurance....so your stuff gets treated like garbage.
Funny part was the shape of the packing looked fine and nothing stuck out at all. But if I had to make these wings and ship them across the US, I would reconsider the packing technique. It was one laver of bible wrap and one layer of thin cardboard all in the shape of the wing, a big V.
I would double up on the cardboard or use denser cardboard than what was used.
Are you running a stock exhaust or modified and how? Side exit, rear exist high or low?
WP dual out the rear without cat, in combination with F4+5 windshield and Stinger top. Fumes were pretty bad. Added a rear windscreen to reduce airflow from circling back in. In talks with Jeff from WP, he has claimed that the addition of the rear wing and tune will eliminate it all. Hoping he is right. I have the fumes reduced a ton compared to when first installed and I can live with it now, but the wife tends to think it is too much.
I am not fond on the idea of putting the cat back on.
It sure does. I'll comment back on how they make it right. 
I ordered the large Underground Autostyling rear wing and it came with a couple big dings which I am positive happened in shipment. There is one on the underside that damaged the coating and I can live with that one. There is one on top that sticks out like a sore thumb and shows structure damage to the fiberglass as it is exposed or poking out and waving at me.
The piece is an awkward shape to ship and I get that. But bummed I will have to hold off installation. I sent the seller an email with the photos and hope they can help fix or replace this quickly. I am on that hunt to remedy my in cabin exhaust smell and this is a critical component. Thanks for letting me vent.
Underneath ding.
Top ding, everyone wave to the exposed fibers.
Just send in your stock ECU to MeFiBurn (Bob) at OBD Diagnostics Inc in southern California. He does wonders.
^ Starting to sound like Commiefornia not Indiana.
Price is $25.00 US Dollars shipping included.
My Paypal account is thebrackleys@gmail.com the company is Photon Laser Art & Design
Sending PayPal for a set @Slingshot Garage. Hope these are still in production!
Edit: Sent as friends and family to minimize fees on your end. Added my forum name in the notes. Will PM you my address.
Mud flaps are for monster trucks!
I do like the rally armor one that protects the angle drive from debris.
Show us some pictures of what you come up with. Cut an extra angle drive one and send it to me. I'll review it for you. 
Great job on that video. This is a pretty good bang for your buck. Would like to hear some more reviews on it.
Sorry to hear this. Nothing worse than having your SS down and worse when it is broken. Best of luck on the repairs.
Indiana rejected my request for Camel6 on an NRA plate. Told me I could have it on any of the other Indiana plates except that one. Reason- I might be advertising guns!! WTF!!!! It happens to be my last name and my uniform # from my college baseball days!! Indiana can be kind of "conservative" to say the least at times!!
CDCAMEL6
That is funny. Never heard of a camel firearm.
