2 miles away and I missed it 😔. Hopefully you guys have another one this year
Posts by Teslasling
-
-
That would be what I use. I was going to tell y'all that after I waited for a little while. Use the Direct Result and it's awesome. I have scored some good stuff with that search engine.What brand lift does rabtech have?
-
Hello Dave,
Thank you for helping out on this
So based on diagram attached from N2MB
Red 16 AWG wire to a fuse
Black wire 16 AWG to splice D pin on all coils - Do you know the best way to get one wire spliced into 4 wires?
BLUE WIRE accelerator position sensor to Throttle body pin #5 TPS +5V REFERENCE OR TPS 1 SIGNAL (CONTI TB TPS 2)
Green wire / Cruise Control Clutch switch - to Momentary switch installed on clutch pedal?
Ignition/ fuel injector control signal to INJ JUMPER OR ? PAGE 6 OF DIAGRAM
Coil Signal is Pin "C"
If you were installing the wot box where would you splice in on the diagram to get coil signal?
This is what you are looking for.
Slingshot Engine 2015 2016.pdf
You can also purchase the entire manual for $15 here https://www.ebay.com/itm/2015-…ee72b5:g:VQgAAOSwTbFdtyEl
Money well spent.
This is what you are looking for.
Slingshot Engine 2015 2016.pdf
You can also purchase the entire manual for $15 here https://www.ebay.com/itm/2015-…ee72b5:g:VQgAAOSwTbFdtyEl
Money well spent.
-
Hello Dave,
So you just need to splice into coil #1 c pin and slice in to all 4 coil power d pins?
Coil Signal is Pin "C"
If you were installing the wot box where would you splice in on the diagram to get coil signal?
This is what you are looking for.
Slingshot Engine 2015 2016.pdf
You can also purchase the entire manual for $15 here https://www.ebay.com/itm/2015-…ee72b5:g:VQgAAOSwTbFdtyEl
Money well spent.
This is what you are looking for.
Slingshot Engine 2015 2016.pdf
You can also purchase the entire manual for $15 here https://www.ebay.com/itm/2015-…ee72b5:g:VQgAAOSwTbFdtyEl
Money well spent.
-
Hello Kyle,
If you were installing the wot box where would you splice in on the diagram to get coil signal?
This is what you are looking for.
Slingshot Engine 2015 2016.pdf
You can also purchase the entire manual for $15 here https://www.ebay.com/itm/2015-…ee72b5:g:VQgAAOSwTbFdtyEl
Money well spent.
This is what you are looking for.
Slingshot Engine 2015 2016.pdf
You can also purchase the entire manual for $15 here https://www.ebay.com/itm/2015-…ee72b5:g:VQgAAOSwTbFdtyEl
Money well spent.
-
Hello Kyle,
If you were installing the wot box where would you splice in on the diagram to get coil signal?
-
Does anyone have 2016.5 pcm wiring diagram? I can not find it
-
no instructions???
-
Hey there, I am driving right now on the way to Louisiana. I should be able to take a better look at the video tomorrow though and will be in touch.
thanks Dave
-
To get Dave's attention Dave@DDMWorks should send him a notice. Generally he is 'Topnotch' to work with. Generally checks in pretty regularly.
I take it your slingshot doesn't sound like that when you turn your motor off?
-
To get Dave's attention Dave@DDMWorks should send him a notice. Generally he is 'Topnotch' to work with. Generally checks in pretty regularly.
Thank you!!
-
-
So I started to drive my slingshot after the new motor and started to hear creaking noise on acceleration and turning off motor. It doesn't make the noise at start up or at idle. It sounds like something is loose but cant seem to locate the noise. It pretty loud and just cant figure it out.
I sent the video to Dave @ddmworks but waiting for a reply
Any ideas would help
-
-
-
-
-
Dave@DDMWorks hello Dave I left a message Friday but no call back. I'm worried and I sent a few videos to Angie. My sling shot is smoking bad and doesn't sound well after the 3rd pull. Another post from a gentleman said something about tuning with Bob in the passenger seat and he heard a pop and did a 2 mile drive with smoke. I heard a pop but assumed it's the back pressure after shifting at 5k. My scg 1 read peak psi was 11psi. I'll wait for Monday to reach out to tech line again.
-
Heres the final setup minus Hahn intake manifold, injectors, fuel rail, and fuel pump
-
So the stage 1 ddmworks
turbo was installed and recvd today. It sounded and felt amazing but The first two pulls read 8 psi the 3rd pull read 11.9 and the exhaust became really loud.. So loud you couldn't hear the turbo spool or hear the waste gate open with that beautiful sound it makes. I have no clue what's going on. Any ideas