I haven't figured that out through here yet lol how and where
Posts by frehleycomet
-
-
.....here's a set I just did for someone and painted them myself...used one pack for each wheel ring (wrapped it around til you have 3 rows on the ring)
You my friend is the one I need to talk with outside this page. Please tell me how I can contact you. I have questions that I know you can answer. Thank you
-
Can anyone PLEASE tell me where I can buy the LED's that go around the Zarate wheel rings. TIA
-
Wow so sorry brother. Prayers to you, your son and family. God is powerful just as much as prayer. Keep the Faith and your son will get through this.
-
Woodruff Dam in Sneads Florida
-
Can someone please tell me which harness on a 2018 SL has the speaker wires. I'm trying to hook up an aftermarket radio but I can't figure out where the speaker wires are so I can connect the radio speaker wires to. Thank you
-
I just removed the stock radio from my 2018 SL. I have a Pioneer aftermarket ready for install. I removed all the wire harnesses from the radio leaving me a clean slate. I have also purchased the power harness from slingtunes.com https://slingtunes.com/shop?olsPage=products%2Fspss18 The power harness has 3 wires red,yellow and black. I don't see any harness on the sling that I just removed from the stock radio that also has the 3 wires like the purchased power harness. I see a harness that might fit but it has 5 wires. Also, the aftermarket Pioneer has all the color coded speaker wires but where are the speaker wires in the sling and are they color coded the same. Most or let's say every video on Youtube are on Slingshots before 2018 and none really explain how to hook up the power harness or even the speaker wires. Anybody that has any knowledge please contact me via email and I'll give my number so we can talk in person instead. Need help bad on this one. Thank you. frehleycomet1@yahoo.com
-
I live in Macon GA. From Bainbridge GA
Sent from my iPhone using Polaris Slingshot Info
Hey neighbor I'm in Thomasville Ga.
-
Has anyone hooked up the stock backup camera to an aftermarket radio? If so how was it done? TIA
-
You will likely need an amp, and most modern aftermarket radios have an amp pre-out for connecting them, but read up on your sound bar, if it has an amp built in, you may be able to go directly from the radio to the bar, assuming your radio has the pre-outs.
Yes the sound bar has a built in amp. My question is which pre-outs from the radio do I use
-
Hello everyone, I'm installing a sound bar on my Slingshot and I need a question answered please. The sound bar has an AV input and an AV output. My question is where on an after market radio do I connect this sound bar so that I can listen to my radio, CD/DVD through the sound bar. The sound bar is Bluetooth ready so I already can listen to music but from my phone though. I want to be able to listen to music that comes from my after market radio. TIA
-
Thanks man it's outta their.
Since I only needed to install a switch and a charger socket I left the radio in and worked around it. BUT I didn't remove the radio because I was not sure how to remove that blue plug.
Jamesgn
Do you know what that blue wire is for though
-
On amazon both front and back are right under $80....EACH...plus shipping....
If you found them can you please share the link?
-
Holy crap a complete set of 4 would be over $350....
The two closest to the windshield were 80 each, not sure what the one for the front cost. The ones in the front are shorter so I don't think they should be as expensive, but then again it is a Slingshot where even a bolt could cost you an arm and a leg
-
Thanks man it's outta their.
Jamesgn
was there a wire on the back of the radio with a blue cap looking thing? If so how did you remove that and do you know what it's for?
-
can you take it to a bicycle shop to see if they can put a new cable in your sleeve?
I tried a bike shop and a lawn mower shop and they couldn't supposedly
-
Looking for a used hood latch release cable for the rear latch. The latch closest to the windshield. New would cost me $80 or so. Total bullshit what this price is for a bike cable pretty much. TIA
-
I used some Krylon chevy orange hi heat (2000 degrees) and the color was close to the stripes on the hood. I then cleaned that off and powder coated them ruby red.
LC
Powder coated ruby red.
I'll see if I can find a chevy orange picture.
Did you have to completely remove the caliper from the hose and then bleed the lines to be able to paint the caliper?
-
Spotted a dark colored SS on 319 in Thomasville Ga turning right at the light from Walmart. Look me up so we can ride.
-
Outside Lights:
https://smile.amazon.com/gp/pr…tle_o01_s00?ie=UTF8&psc=1
I removed the rubber boot, cut out the center 1", removed the wires from the boot, cut the stock wires and used butt connectors to wire them to the LED (Yellow wires are the Positive). Fully weather taped the butt connectors.
Inside Lights:
https://smile.amazon.com/gp/pr…tle_o02_s00?ie=UTF8&psc=1
the existing plugs work, the old bulb comes out by doing a short rotation of the bulb assy. The new unit will go in easily but sets a little loose in the socket. I added a couple of dabs of silicone sealant on ether side of the housing to light and let set for a couple of hours.
I just got the H3 for my Slingshot. Do they mount the same way as the stock lights. I mean with the locking pin that holds them in. TIA