Water hydroplaned my Slingshot near LYNNWOOD WA. and a concrete barrier jumped out and bit my front wheel bent my tire rod!
Sent from my iPhone using Polaris Slingshot Forum mobile app
Water hydroplaned my Slingshot near LYNNWOOD WA. and a concrete barrier jumped out and bit my front wheel bent my tire rod!
Sent from my iPhone using Polaris Slingshot Forum mobile app
Sorry to hear about that, for sure. Isn't it like, 4 AM out there?
You got someone coming for you?
I have to assume because it has been 2hrs and no reply to @'KayTwo''s question that you have some help already. This is a good example of a situation where having a "SS Rescue" set up similar to the GWRRA's Gold Book would come in handy.
sorry to hear that but hey, no one got hurt, that we know of anyways, the sling can be fixed, stay safe
I have to assume because it has been 2hrs and no reply to @'KayTwo''s question that you have some help already. This is a good example of a situation where having a "SS Rescue" set up similar to the GWRRA's Gold Book would come in handy.
No help as of yet. I will cup thinking about this and then went back to bed. But now it’s almost 8 AM and hoping someone will message me soon
Sent from my iPhone using Polaris Slingshot Forum mobile app
So is your Sling still on the side of the road and needs a tow, or you have it at home and need some assistance in fixing it, or...?
So is your Sling still on the side of the road and needs a tow, or you have it at home and need some assistance in fixing it, or...?
I am 200 miles from home and manage to hobble it to the next exit and a hotel.
Besides other damage that is mostly superficial, the tie rod has a bad kink in it. I will try to watch this post while I am inquiring around to find a mechanic or someone with tools that I can straighten the tire rod for now. Then I will return all and miss the Oyster run at Anacortes Wa
Sent from my iPhone using Polaris Slingshot Forum mobile app
I am 200 miles from home and manage to hobble it to the next exit and a hotel.
Besides other damage that is mostly superficial, the tie rod has a bad kink in it. I will try to watch this post while I am inquiring around to find a mechanic or someone with tools that I can straighten the tire rod for now. Then I will return all and miss the Oyster run at Anacortes Wa
Straightening it might be tough, and certainly not permanent.
@Slingrazor, @MACAWS (or anyone else), do you know if the tie rod for the slingshot is a readily available commercial product, or is it Polaris-only?
@silver fox, glad you're ok, that's the most important thing. Parts can be fixed.
I suspect you have already found this: Find a Dealer | Polaris Slingshot
Unfortunately there is no help from the dealers until tomorrow at the earliest.
Best of luck,
Bill
Lynnwood Washington is on I five just north of Seattle. I’m from Oregon and don’t know anyone in the area here. Almost 9 AM and stranded. No mechanic shops open
Sent from my iPhone using Polaris Slingshot Forum mobile app
Unfortunately Lynnwood is 180 miles from me and farther from @BryanL. I have a houseguest today that just got out of the hospital from a major surgery and is convalescing here until he can drive home to the Oregon coast. I'm not sure what I can do to help. Without seeing the extent of the bend, straightening a tie rod could be a challenging roadside fix and risks breaking it. That's usually the result in the woods. I don't know if driving it home like that on the freeway would be my choice. I don't have a trailer that fits the Slingshot but perhaps a U-Haul with a wooden plank in the center like @Nemesis1701 has done would get it home. Keep us posted @silver fox. I wish I was closer.
Trailside fix with bailing wire - NOT freeway worthy!
Unfortunately Lynnwood is 180 miles from me and farther from @BryanL. I have a houseguest today that just got out of the hospital from a major surgery and is convalescing here until he can drive home to the Oregon coast. I'm not sure what I can do to help. Without seeing the extent of the bend, straightening a tie rod could be a challenging roadside fix and risks breaking it. That's usually the result in the woods. I don't know if driving it home like that on the freeway would be my choice. I don't have a trailer that fits the Slingshot but perhaps a U-Haul with a wooden plank in the center like @Nemesis1701 has done would get it home. Keep us posted @silver fox. I wish I was closer.
Trailside fix with bailing wire - NOT freeway worthy!
It has about 15° band I will try to post a pic
Sent from my iPhone using Polaris Slingshot Forum mobile app
Maybe you should have mounted your gremlin bell closer to the rear, where when the gremlins drop off they cannot jump back on?
(Sorry if the humor is inappropriate at this time?)
Bill
My non-expert opinion is that it is likely to break if you fully straighten it and, if not, could break under power. If it were me, I would either replace it or trailer it home. The chances of a nearby dealer having that part in stock might not be too high. Does anyone out here on the west coast have a trailer? I could get up there tomorrow.
@silver fox sorry for the bent TR. I'm on the opposite end of the country so can only offer some possible field repair suggestion. Unfortunately the SS does not come with a scissor Jack but if you can source one there is one possible method. Place the scissor jack under the bent section, and secure to the top of the Jack base with whatever is available. Cord, strap or even good old duck tape. The trick will be to keep the bent section from rotating and you start to Jack up. Unfortunately the SS does not have a lot of weight so I'm unsure if it will do much to straighten out. This is sometimes used on off-road trail rides on Jeep's. We usually have a lot more tools to make this work. Hell I always carried spares but that's not helping you, sorry. This may be worth trying if you are just sitting and have nothing else to do.
@silver fox sorry for the bent TR. I'm on the opposite end of the country so can only offer some possible field repair suggestion. Unfortunately the SS does not come with a scissor Jack but if you can source one there is one possible method. Place the scissor jack under the bent section, and secure to the top of the Jack base with whatever is available. Cord, strap or even good old duck tape. The trick will be to keep the bent section from rotating and you start to Jack up. Unfortunately the SS does not have a lot of weight so I'm unsure if it will do much to straighten out. This is sometimes used on off-road trail rides on Jeep's. We usually have a lot more tools to make this work. Hell I always carried spares but that's not helping you, sorry. This may be worth trying if you are just sitting and have nothing else to do.
I wish I could try that! But for some reason I have not found the jack on my slingshot yet!!
Stranded searching for a mechanic, none to be found I’m at the corner of 44th Ave., West and Alderwood in Lynnwood just north of Seattle my phone 971-301-3329
Sent from my iPhone using Polaris Slingshot Forum mobile app
I wish you luck
Outside looking at mine now and you wouldn't be able to get the Jack in the correct spot anyway - A-Arm is in the way more than I remembered. I'll noodle a bit more.
Do you have any tools with you?
If you can remove the TRE from the knuckle you can try the same trick noted without a jack. Unfortunately this will require a long pipe. If disconnect you can push the wheel/tire back out of the way. Rotate the TRE tube so that the bend is facing up and then raise it until it hits your sway bar. Using the same strap, cord, duck tape method secure it to the sway day (bend up). The pipe would then be slipped over the end and you would pull up on the bar until it is as straight A's possible. Sorry because now the issue is getting a pipe. If someone can find a hardware store they usually have pre-cut black pipe in the correct ID and length.